EcoWooD can be extruded into many different shapes and can be worked with conventional woodworking tools.
Below is a selection of extrusions EcoWooD is currently available in, we can also create custom extrusion on special request.
 |
BEARER 36mm x 70mm per ft. run: 0.55kg |
 |
FLAT PANEL 15mm x 127mm per ft. run: 0.78kg |
 |
BEARER 50mm x 100mm per ft. run: 0.90kg |
 |
FLAT PANEL 8mm x 260mm per ft. run: 0.83kg |
 |
BEARER 50mm x 100mm per ft. run: 1.20kg |
 |
HOLLOW PANEL 18mm x 185mm per ft. run: 0.85kg |
 |
BEARER 38mm x 140mm per ft. run: 0.98kg |
 |
M PROFILE 25mm x 150mm per ft. run: 0.93kg |
 |
COLUMN 127mm x 127mm per ft. run: 2.05kg |
 |
SOLID BLOCK 18mm x 35mm per ft. run: 0.25kg |
 |
CYLINDRICAL 7mm x 32mm dia. per ft. run: 0.22kg |
 |
SOLID BLOCK 20mm x 44mm per ft. run: 0.34kg |
 |
DOOR JAMB 44mm x 130mm per ft. run: 0.85kg |
 |
SOLID BLOCK 28mm x 36mm per ft. run: 0.39kg |
 |
FLAT PANEL 6mm x 100mm per ft. run: 0.23kg |
 |
SKIRTING BOARD 18mm x 67mm per ft. run: 0.46kg |
 |
FLAT PANEL 15mm x 100mm per ft. run: 0.65kg |
 |
TONGUE & GROOVE 18mm x 185mm per ft. run: 0.89kg |
 |
U PROFILE 25mm x 100mm per ft. run: 0.64kg |
 |
DECKING 30mm x 100mm per ft. run: 0.77kg |
FRC Data Sheet
| Property | Test Standard | Value |
|---|---|---|
| Tensile Strength | ASTM D 638 | 15.9 MPa |
| Flexural Strength | ASTM D 790 | 280 MPa |
| Flexural Strength | ASTM D 790 | 1582 MPa |
| Failure Load | ASTM D 1761 | 1.5 KN |
| Heat Reversion | BS EN 743: 1995 BS 2782: Part 11 Method 1102B/95 |
0.45% |
| Water Absorption | ASTM D 570 | 0.34 % |
| Mean Coefficient of Linear Thermal Expansion | ASTM 831 | 3.1 x 102 μm/m0 C |
| Average Rate of Burning | ASTM D 635 | 59 seconds |
| Average Extent of Burning | ASTM D 635 | 0 mm |
| Specific Gravity | ASTM D 792 | 1.21 |
| Horizontal Drop Test | Client specification Drop Height 1.2m |
No cracks/breaks in all specimens tested |
| Vertical Drop Test | Client specification Drop Height 1.2m |
No cracks/breaks in all specimens tested |
| Impact Resistance | Client specification Drop Height 1.2m |
No cracks/breaks in all specimens tested |
| Resistance to Termite Attack | FRIM Test Method | 3.6 |
| Melt Flow Index | ASTM D 123 8-88 | 2.66 g / 10 minutes |
| Compressive Strength | ASTM D 695 | |
| Vertical Deflection | Main Roads/Western Australia Document 7205/03-12.96 Specification 602 Annexure 602C Guide Post Rigidity Test | 0.2mm (Load 600mg) |
| Angular Deviation | Main Roads/Western Australia Document 7205/03-12.96 Specification 602 Annexure 602C Guide Post Rigidity Test | Less than 45° (Load 600mg) |